The Fundamentals of Plumbing Knowledge When Installing a Bathtub
The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Blog Article
The writer is making a number of great annotation related to How to Install a Bathtub Yourself overall in the article which follows.
Mounting a bathtub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old tub with a new one is likewise a reasonably difficult project. If the old bathtub is easily available, the project can relocate easily; if you have to open up a wall surface to remove the old bathtub and place the new bathtub, the job is much harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to vacate the old tub and also set in the new one. Ensure you have actually certified yourself for the task and are comfortable trying it. Instead of hiring a professional to take control of a halfway-completed task, it is far better to consider utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube links.
This article will certainly aid you mount a brand-new tub in your bathroom if you have actually already purchased a new bathtub and don't need to transform the arrangement of your previous water supply pipelines.
Your devices and also material list need to make up the following:
Planning for the Installation
Firstly, the sustaining frame supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps unit to avoid pressure on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last position.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be quite problematic because of the limited gain access to that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have actually been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before going on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, put the bath tub in the called for setting. The wooden boards are handy in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the tub till the level reviews degree.
To mount taps, fit all-time low of the outermost adaptable tap port to the appropriate supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water supply and also check all joints as well as new pipework for leakages and also tighten them if required. Fill the tub as well as likewise examine the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the bath tub should wait up until the tub has actually been made use of at least when as this will certainly settle it right into its final position.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines are in location between the faucet and the sink. Protect the faucet in place with the manufacturer offered backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type ought to be linked to the tap finishes initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall between the bath and also the tiling, leading to issues with dampness as well as possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bathtub with water before securing, to permit the activity experienced when the tub is in use. The sealer can crack relatively very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that piece of content was sensible. Appreciated our piece of writing? Please share it. Help other people locate it. We treasure reading our article about How to Install a Bathtub.
Quick, reliable, call! Report this page